Step 1<\/strong><\/p>\n\n\n\nGather your supplies<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 2<\/strong><\/p>\n\n\n\nUsing the templates included in your PDF instrutions, print the designs on paper and save them for the applique stars that come later in the project. Then, enlarge the designs by 20% and print on StabilStick template sheets.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 3<\/strong><\/p>\n\n\n\nGather your fabric and batting rectangles.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 4<\/strong><\/p>\n\n\n\nMark 1″ from each edge of the fabric rectangle. This will be the edge of your placemat. <\/p>\n\n\n\n <\/figure>\n\n\n\nStep 5<\/strong><\/p>\n\n\n\nTrim the StabilStick Template sheets close to the designs. Position them on the front fabric and plan where you’ll stitch. The Stars & Stripes Quilting designs are continuous. In this example, the first design is placed about 5″ from the lower right corner.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 6<\/strong><\/p>\n\n\n\nOnce you’re happy with your design placements, make horizontal marks to line up with their centers. <\/p>\n\n\n\n <\/figure>\n\n\n\n Step 7<\/strong><\/p>\n\n\n\nUse 505 Adhesive Spray to attach all layers of your placemat: front, batting, and backing.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 8 <\/strong><\/p>\n\n\n\nPeel the paper from the template sheet and stick it down on the placement line. Do not discard the paper backing – this template is reusable!<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 9<\/strong><\/p>\n\n\n\nWind a bobbin with matching thread – we used 9918 Ol’ Glory Isacord Variegated.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 10 <\/strong><\/p>\n\n\n\nYour embroidery will be close to the edge, so you’ll need to add Ultra Clean and Tear Plus to the 1″ edges of the placemat. Cut (3) 5″x24″ pieces of Ultra Clean and Tear Plus. Tape the bottom edge of the placemat to one of the strips of Ultra Clean and Tear Plus with TearAway Tape.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 11<\/strong><\/p>\n\n\n\nUse the Grippy Grid to keep your hoop in place while you hoop the quilt sandwich.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 12<\/strong><\/p>\n\n\n\nBring up the design and get ready to stitch. Turn off the knotting setting for the beginning and end of the design – it’s already built in<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 13<\/strong><\/p>\n\n\n\nUse the placement tool on your embroidery machine to find the center of your design<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 14<\/strong><\/p>\n\n\n\nOnce you’ve found your placement, remove the template sheet and return it to its paper backing.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 15<\/strong><\/p>\n\n\n\nBring up the bobbin thread and hold the threads gently while you stitch the first few stitches. Trim threads.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 16<\/strong><\/p>\n\n\n\nStitch the design.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 17<\/strong><\/p>\n\n\n\nCut one of your long strips of Ultra Clean and Tear Plus in half to measure 5″x12″ and tape to the left side of the placemat with TearAway Tape.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 18<\/strong><\/p>\n\n\n\nLine up the template sheet with the previous design.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 19<\/strong><\/p>\n\n\n\nRe-hoop, then use the placement tools on your machine to line up the next design and stitch. <\/p>\n\n\n\n <\/figure>\n\n\n\nStep 20<\/strong><\/p>\n\n\n\nRepeat on the other side (adding stabilizer, then stitching) until the top row is completed.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 21<\/strong><\/p>\n\n\n\nFor the second row, place your template where you’d like the first design to be stitched in relation to the first row. We offset ours to nest between the previous row’s designs with about \u00bd\u201d space. <\/p>\n\n\n\n <\/figure>\n\n\n\nStep 22<\/strong><\/p>\n\n\n\nAdd your Ultra Clean and Tear Plus, then stitch until the entire row has been completed in the same way as the first row. Remove excess stabilizer.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 23<\/strong><\/p>\n\n\n\nGrab your printed designs from Step 2 (at actual size). Tape the printed design to your lightbox or a window, then place a sheet of Applique Fuse and Fix over top. Darkening the star with pencil can make the design easier to see. Trace however many stars you’d like to add to your placemats, keeping in mind which ones will be red, white, or blue. This allows you to get as many stars as possible onto one page and save material!<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 24<\/strong><\/p>\n\n\n\nPress the fusible side of Applique Fuse and Fix to the wrong side of the Luxe Sparkle Vinyl.<\/p>\n\n\n\n <\/figure>\n\n\n\nStep 25<\/strong><\/p>\n\n\n\nCut out all of your stars and position them on your placemat. Use the scoring tool in the OESD Embroidery Essentials Tool Kit to remove the paper backing.<\/p>\n\n\n\n\n <\/figure>\n\n\n\n <\/figure>\n<\/figure>\n\n\n